IC HT12D PDFIC HT12D PDF

HT12D is a series decoder IC for remote control applications manufactured by Holtek. It is commonly used for radio frequency (RF) applications. Download. RF transmitter and RF receiver of Mhz; 3 push buttons; IC HT12D; IC HT12E; Hearders (male or female it doesn’t care); 3 resistors with a value from ( to. HT12D is a decoder integrated circuit that belongs to series of decoders. This series of decoders are mainly used for remote control system applications, like.

Author: Dakree Arashigal
Country: Egypt
Language: English (Spanish)
Genre: Technology
Published (Last): 28 December 2014
Pages: 114
PDF File Size: 15.56 Mb
ePub File Size: 8.52 Mb
ISBN: 544-3-17544-270-8
Downloads: 68595
Price: Free* [*Free Regsitration Required]
Uploader: Zujind

These two ICs together form an Encoder and Decoder pair. It is very important that your Decoder should have the same address of that of the encoder. In simple terms, HT12D converts the serial input into parallel outputs.

TL — Programmable Reference Voltage. In the above circuit Bt12d have set the 8-bit address data as 0b, by connecting all address pins to ground. What is Web Browser.

It is not mandatory to use it.

HT12D RF Decoder IC Pinout, Details, Equivalent & Datasheet

Interface GPS with Arduino. Connected to the Ground of circuit. This high-density System-in-Package SiP integrates controller, power switches, and support components. This series of decoders are mainly used for remote control system applications, like burglar alarm, car door controller, security system etc. The serial input data is compared with the local addresses three times continuously.

So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to hg12d data. If any valid data is received they can be obtained from these four pins.

  M170EG01 VD PDF

uc

This oscillator can be used by connecting these two pins through a 1M Resistor. For decoding bt12d data the IC will requires an oscillatorluckily this IC has one in-built. This pin will go high when a data is received. Choosing Motor For Robots. HT12D hht12d capable of decoding 12 bits, of which 8 are address bits and 4 are data bits.

Submitted by admin on 27 October So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. SPI Module of Arduino. A basic circuit diagram for the HT12D IC is shown below In the above circuit I have set the ht21d address data as 0b, by connecting all address pins to ground.

Supply voltage; 5V 2. Virgin Galactic — Commercial Space Flight. The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded. Valid transmission; active high. To know how a 4-bit data can be encoded and then send to the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is given here.

HT12D is a decoder integrated circuit that belongs to 2 12 series of decoders. These are the 8-bit address bits, which is used to protect your data. We should set the bits in same pattern on Encoder and Decoder IC to pair them. It is mainly provided to interface RF and infrared circuits.

  ASM HANDBOOK VOLUME 14B PDF

If you want security ht12c can connect any of the 8 pins to 5V to make it high.

HT12D Decoder IC

The 4-bit data that is received can be obtained on pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7.

It decodes the serial addresses and data received by, say, an RF receiver, into ht1d data and sends them to output data pins.

This pin powers the IC should use only 5V. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. The data on 4 bit latch type output pins remain unchanged until new is received.

A valid transmission in indicated by a high signal at VT pin. Arduino based GPS receiver.

The Encoded 12 bit output data obtained from HT12E has to be given here. This oscillator can be used by connecting these two pins through a 1M Resistor 17 Valid Transmission VT This pin will go high when a data is received. Skip h1t2d main content. They can also be connected to LED to physically view the received data.

How IC HT12D works?

The IC has a built in oscillator. The input data code is decoded when h1t2d error or unmatched codes are found. Interface SD Card with Arduino.